21st ESV Conference 2009
Filtern
Schlagworte
- Conference (8)
- Konferenz (8)
- Accident (4)
- Anthropometric dummy (4)
- Dummy (4)
- Unfall (4)
- Accident prevention (2)
- Bewertung (2)
- Biomechanics (2)
- Biomechanik (2)
Institut
- Abteilung Fahrzeugtechnik (9)
- Sonstige (9)
- Präsident (1)
In the EC FP6 Integrated Project Advanced Protection Systems, APROSYS, the first WorldSID small female prototype was developed and evaluated by BASt, FTSS, INRETS, TRL and UPM-INSIA during 2006 and 2007. Results were presented at the ESV 2007 conference (Been et al., 2007). With the prototype dummy scoring a biofidelity rating higher than 6.7 out of 10 according to ISO/TR9790, the results were very promising. Also opportunities for further development were identified by the evaluation group. A revised prototype, Revision1, was subsequently developed in the 2007-2008 period to address comments from the evaluation group. The Revision1 dummy includes changes in the half arms and the suit (anthropometry and arm biomechanics), the thorax and abdomen ribs and sternum (rib durability), the abdomen/lumbar area and the lower legs (mass distribution). Also a two-dimensional chest deflection measurement system was developed to measure deflection in both lateral and anterior-posterior direction to improve oblique thorax loading sensitivity. Two Revision1 prototype dummies have now been evaluated by FTSS, TRL, UPM-INSIA and BASt. The updated prototype dummies were subjected to an extensive matrix of biomechanical tests, such as full body pendulum tests and lateral sled impact tests as specified by Wayne State University, Heidelberg University and Medical College of Wisconsin. The results indicated a significant improvement of dummy biofidelity. The overall dummy biofidelity in the ISO rating system has significantly improved from 6.7 to 7.6 on a scale between 0-10. The small female WorldSID has now obtained the same biofidelity rating as the WorldSID mid size male dummy. Also repeatability improved with respect to the prototype. In conclusion the recommended updates were all executed and all successfully contributed in achieving improved performance of the dummy.
Powered Two Wheelers (PTWs) accidents constitute one of the road safety problems in Europe. PTWs fatalities represent 22% at EU level in 2006, having increased during last years, representing an opposite trend compared to other road users" figures. In order to reduce these figures it is necessary to investigate the accident causation mechanisms from different points of view (e.g.: human factor, vehicle characteristics, influence of the environment, type of accident). SAFERIDER project ("Advanced telematics for enhancing the SAFEty and comfort of motorcycle RIDERs", under the European Commission "7th Framework Program") has investigated PTW accident mechanisms through literature review and statistical analyses of National and In-depth accident databases; detecting and describing all the possible PTW's accident configurations where the implementation of ADAS (Advanced Driver Assistance Systems) and IVIS (In-Vehicle Information Systems) could contribute to avoid an accident or mitigate its severity. DIANA, the Spanish in-depth database developed by CIDAUT, has been analyzed for that purpose. DIANA comprises of accident investigation teams, in close cooperation with police forces, medical services, forensic surgeons, garages and scrap yards. An important innovation is the fact that before injured people arrive to hospitals, photographs and explanations about the possible accident injury mechanisms are sent to the respective hospitals (via 3G GPRS technology). By this, additional information to medical staff can be provided in order to predict in advance possible internal injuries and select the best medical treatment. This methodology is presented in this paper. On the other hand, the main results (corresponding to road, rider and PTW characteristics; pre and post-accident manoeuvres; road layout; rider behaviour; impact points; accident causations;...) from the analyses of the PTW accidents used for SAFERIDER are shown. Only accident types relevant to ADAS and IVIS devices have been considered.
Since its beginning in 1999, the German In-Depth Accident Study (GIDAS) evolved into the presumably leading representative road traffic accident investigation in Europe, based on the work started in Hanover in 1973. The detailed and comprehensive description of traffic accidents forms an essential basis for vehicle safety research. Due to the ongoing extension of demands of researchers, there is a continuous progress in the techniques and systematic of accident investigation within GIDAS. This paper presents some of the most important developments over the last years. Primary vehicle safety systems are expected to have a significant and increasing influence on reducing accidents. GIDAS therefore began to include and collect active safety parameters as new variables from the year 2005 onwards. This will facilitate to assess the impact of present and future active safety measures. A new system to analyse causation factors of traffic accidents, called ACASS, was implemented in GIDAS in the year 2008. The whole process of data handling was optimised. Since 2005 the on-scene data acquisition is completely conducted with mobile tablet PCs. Comprehensive plausibility checks assure a high data quality. Multi-language codebooks are automatically generated from the database structure itself and interfaces ensure the connection to various database management systems. Members of the consortium can download database and codebook, and synchronize half a terabyte of photographic documentation through a secured online access. With the introduction of the AIS 2005 in the year 2006, some medical categorizations have been revised. To ensure the correct assignment of AIS codes to specific injuries an application based on a diagnostic dictionary was developed. Furthermore a coding tool for the AO classification was introduced. All these enhancements enable GIDAS to be up to date for future research questions.
A flexible pedestrian legform impactor (FlexPLI) with biofidelic characteristics is aimed to be implemented within global legislation on pedestrian protection. Therefore, it is being evaluated by a technical evaluation group (Flex-TEG) of GRSP with respect to its biofidelity, robustness, durability, usability and protection level (Zander, 2008). Previous studies at the Federal Highway Research Institute (BASt) and other laboratories already showed good progress concerning the general development, but also the need for further improvement and further research in various areas. An overview is provided of the different levels of development and all kinds of evaluation activities of the Flex-TEG, starting with the Polar II full scale pedestrian dummy as its origin and ending up with the latest legform impactor built level GTR that is expected to be finalized by the end of the year 2009. Using the latest built levels as a basis, gaps are revealed that should be closed by future developments, like the usage of an upper body mass (UBM), the validation of the femur loads, injury risk functions for the cruciate knee ligaments and an appropriate certification method. A recent study on an additional upper body mass being applied for the first time to the Flex-GT is used as means of validation of recently proposed modified impact conditions. Therefore, two test series on a modern vehicle front using an impactor with and without upper body mass are compared. A test series with the Flex-GTR will be used to study both the comparability of the impact behavior of the GT and GTR built level as well as the consistency of test results. Recommendations for implementation within legislation on pedestrian protection are made.
According to the German road traffic regulations children up to the age of 12 or a height below 150 cm have to use approved and appropriate child restraint systems (CRS). CRS must be approved according to UN-ECE Regulation No. 44. The regulation classifies CRS in 5 weight categories. The upper weight group is approved for children from 22 to 36 kg. However, studies show that already today many children weigh more than 36 kg although they have not reached a height of 150 cm. Therefore, no ECE R44 approved CRS is available for these overweight children. In conclusion, today's sizes and weights of children are no longer represented by the current version of the ECE R44. The heaviest used dummy (P10) weighs just 32.6 kg and has a height of 137.9 cm. Statistical data of German children show that already 5% of the children at a height of 137.9 cm have a weight above 45.3 kg. Regarding children at a height of 145 cm, the 95th percentile limit is at a weight of 53.3 kg. Based on these data 4 dummies with different heights and weights were defined and produced. Two of them are overweight. Up to now, there is no experience how current child restraint systems perform in a car crash if they are used by children with a weight above 36 kg and a height smaller than 150 cm. In the future, different child restraint systems will be tested with respect to the ECE R44 regulation using these overweight dummies.
The head impact of pedestrians in the windscreen area shows a high relevance in real-world accidents. Nevertheless, there are neither biomechanical limits nor elaborated testing procedures available. Furthermore, the development of deployable protection systems like pop-up bonnets or external airbags has made faster progress than the corresponding testing methods. New requirements which are currently not considered are taken into account within a research project of BASt and the EC funded APROSYS (Advanced PROtection SYStems) integrated project relating to passive pedestrian protection. Testing procedures for head impact in the windscreen area should address these new boundary conditions. The presented modular procedure combines the advantages of virtual testing, including full-scale multi-body and finite element simulations, as well as hardware testing containing impactor tests based on the existing procedures of EEVC WG 17. To meet the efforts of harmonization in legislation, it refers to the Global Technical Regulation of UNECE (GTR No. 9). The basis for this combined hardware and virtual testing procedure is a robust categorization covering all passenger cars and light commercial vehicles and defining the testing zone including the related kinematics. The virtual testing part supports also the choice of the impact points for the hardware test and determines head impact timing for testing deployable systems. The assessment of the neck rotation angle and sharp edge contact in the rear gap of pop-up bonnets is included. For the demonstration of this procedure, a hardware sedan shaped vehicle was modified by integrating an airbag system. In addition, tests with the Honda Polar-II Dummy were performed for an evaluation of the new testing procedure. Comparing these results, it was concluded that a combination of simulation and updated subsystem tests forms an important step towards enhanced future pedestrian safety systems considering the windscreen area and the deployable systems.
Evaluation of the performance of competitive headforms as test tools for interior headform testing
(2009)
The European Research Project APROSYS has evaluated the interior headform test procedure developed by EEVC WG 13, representing the head contact in the car during a lateral impact. One important aspect within this test procedure was the selection of an appropriate impactor. The WG13 procedure currently uses the Free Motion Headform as used within the FMVSS 201. The ACEA 3.5 kg headform used in Phase 1 of the European Directive and the future European Regulation on Pedestrian Protection is still discussed as a possible alternative. This paper reports work performed by the Federal Highway Research Institute (BASt) as a part of the APROSYS Task 1.1.3. The study compares the two headform impactors according to FMVSS and ACEA, in a series of basic tests in order to evaluate their sensitivity towards different impact angles, impact accuracy, the effect of differences to impactors of the same type and the effects of the repeatability and reproducibility of the test results. The test surface consisted of a steel tube covered with PU foam and PVC, representing the car interior to be tested. Despite of the higher mass of the FMH the HIC values of this impactor were generally lower than those of the ACEA headform. The FMH showed a higher repeatability of test results but a high sensitivity on the angle of roll, the spherical ACEA impactor performed better with regards to the reproducibility. In case of the ACEA impactor-, the angle of roll had no influence.
Technical progress in automotive engineering focuses at the moment on two competing branches: improving safety and reducing energy consumption. Recent consideration has been given to a third factor, cost to the consumer. Challenges are presented by demographic changes, especially with increasing participation of elderly people in road traffic. The report considers the recent history of road accidents in Germany and statistics relating to vehicle population and road performance. There is a general trend towards decreasing numbers of accidents and their severity. Transport is responsible for roughly 20% of CO2 emissions and approximately 70% of total petroleum consumption. The Federal Government has responded to these challenges by publishing the Freight Transport and Logistics Masterplan in the summer of 2008. It describes the strategic transport policy direction and the key elements of the future course of action which are to be used to ensure the provision of efficient infrastructure and, at the same time, to reduce the amount of energy consumed by vehicles and make transport more efficient, cleaner and quieter. This document contains a number of concrete measures subsumed under the following six objectives: Making optimum use of transport infrastructure - shaping transport to make it more efficient; Reducing the number of journeys - ensuring mobility; Transferring more traffic to the railways and inland waterways; Upgrading more transport arteries and hubs; Environmentally friendly, climate friendly, quiet and safe transport, and Good working conditions and good training in the freight transport industry. Progress in research is outlined in the following areas: Daytime Running Lights for Motorcycles; Safety of hydrogen vehicles - addressing safety and environmental issues by development of a Global Technical Regulation for hydrogen vehicles; Elements of active vehicle safety for elderly drivers; Periodical Technical Inspection of electronically controlled systems in road vehicles - Electronic Stability Control; Pedestrian protection; Crash Compatibility - role of collision partner in passive safety tests; Child safety; Euro NCAP - Child Restraint Systems, and German Field Operational Test on Car-to-Car and Car-to-Infrastructure Systems (SIM-TD). The research project AKTIV - "Adaptive and Cooperative Technologies for Intelligent Traffic" encompasses the design, development, and evaluation of novel driver assistance systems, knowledge and information technologies and is set up to find solutions for efficient traffic management and Car-to-Car and Car-to-Infrastructure communication for future cooperative vehicle applications. The European Statement of Principles on the Human Machine Interface (HMI), presented at the eSafety Conference, which was held in Berlin on 5/6 June 2007, addresses issues such as Real Time Traffic Information (RTTI), Legal issues of Advanced Driver Assistance Systems (ADAS) and e-security.
Within the process of integrating passenger airbags in the vehicle fleet a problem of compatibility between the passenger airbag and rear-facing child restraint systems was recognised. Especially in the US several accidents with children killed by the passenger airbag were recorded. Taking into account these accidents the deactivation of a present passenger airbag is mandatory if a child is carried in a rear-facing child restraint system at the front passenger seat in all member states of the European Union. This rule is in force since the deadline of 2003/20/EC at the latest. In the past a passenger airbag either could not be disabled or could only be disabled by a garage. Today there are a lot of different possibilities for the car driver himself to disable the airbag. Solutions like an on/off-switch or the automatic detection of a child restraint system are mentioned as an example. Taking into account the need for the deactivation of front passenger airbags two types of misuse can occur: transportation of an infant while the airbag is (still) enabled and transportation of an adult, while the airbag is disabled, respectively. Within a research project funded by BASt both options of misuse were analysed utilising two different types of surveys amongst users (field observations and interviews, Internet-questionnaires). In addition both analysis of accident data and crash tests for an updated assessment of the injury risk caused by the front passenger airbag were conducted. Both surveys indicate a low risk of misuse. Most of the misuse cases were observed in older cars, which offer no easy way to disable the airbag. For systems, which detect a child seat automatically, no misuse could be found. The majority of misuses in cars equipped with a manual switch were caused by reasons of oblivion. Also the accident analysis indicates a minor risk of misuse. From more than 300 cases of the GIDAS accident sample that were analysed, only 24 children were using the front passenger seat in cars equipped with a front passenger airbag. In most of these cases the airbag was deactivated. When misuse occurred the injury severity was low. However, when analysing German single accidents the fatality risk caused by the front passenger airbag became obvious. From the technical point of view, there were important changes in the design of passenger airbags in recent years. Not only volume and shape were modified, but also the mounting position of the entire airbag module was changed fundamentally. Even if these findings do not allow obtaining general conclusions, a clear tendency of less danger by airbags could be identified. For future vehicle development a safe combination of airbags and rear faced baby seats seems to be possible in the long term. This would mean that both types of misuse could be eliminated. For parents an easier use of child seat and car would be the result.
In the last years there has been a decline in accident figures in Germany especially for four wheeled vehicles. At the same time, accident figures for motorcycles remained nearly constant. About 17 % of road traffic fatalities in the year 2006 were motorcyclists. 33 % of these riders were killed in single vehicle crashes. This leads to the conclusion that improving driving dynamics and driving stability of powered two wheelers would yield considerable safety gains. However, the well-known measures for cars and trucks with their proven effectiveness cannot be transferred easily to motorcycles. Therefore studies were carried out to examine the safety potential of Anti Lock Braking Systems (ABS) and Vehicle Stability Control (VSC) for motorcycles by means of accident analysis, driving tests and economical as well as technical assessment of the systems. With regard to ABS, test persons were assigned braking tasks (straight and in-curve) with five different brake systems with and without ABS. Stopping distances as well as stress and strain on the riders were measured for 9 test riders who completed 105 braking manoeuvres each. Knowing the ability of ABS to avoid falls during braking in advance of a crash and taking into account the system costs, a cost benefit analysis for ABS for motorcycles was carried out for different market penetration of ABS, i.e. equipment rates, and different time horizons. The potential of VSC for motorcycles was estimated in two steps. First the kinds of accidents that could be prevented by such a system at all have been analysed. For these accident configurations, simulations and driving tests were then performed to determine if a VSC was able to detect the critical driving situation and if it was technically possible to implement an actuator which would help to stabilise the critical situation.
