620 Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
- 2010 (31) (entfernen)
Dokumenttyp
Schlagworte
- Conference (31) (entfernen)
Institut
Every second counts when human lives are at stake. The increasingly safe design of vehicles presents rescuers with a serious challenge. Faced with high-strength steels and body reinforcements, even the most powerful cutters reach their limits. Therefore, incident commanders require information on the technical features and components installed, directly in the vehicle. Several tests have shown that such information helps to save valuable minutes. Therefore, a standardised A4 "rescue sheet" containing information on the location of cabin reinforcements, the tank, the battery, airbags, gas generators, control units etc. " and indicating adequate cutting points must be used throughout Europe. Hopefully, in a few years, the new eCall emergency call system will be in place everywhere in Europe. The system will transmit the relevant vehicle-specific data directly to the rescuers on-site. Until then, we need a simple and effective solution that saves lives.
The role of a national motor vehicle crash causation study-style data set in rollover data analysis
(2010)
On 1 January 2005, The National Highway Traffic Safety Administration, an agency of the United States Department of Transportation, implemented a new data collection strategy designed to assess crash avoidance technologies and report associated behavioral inputs and outcomes. The original goal was a six-year program, however, during the shortened data collection period; it proved a valuable resource for understanding a precrash environment previously obscured by forensic case investigation. Another unintended consequence was an overlap with infrastructure, roadway geometry, and design with the occupant and vehicle outcomes, by virtue of well-defined attributes. External to the collected data, supplementary information was extrapolated, by using manuals published in the United States, by the American Association of State Highway Transportation Officials and selected State Departments of Transportation, in conjunction with the National Motor Vehicle Crash Causation Study (NMVCCS). This provided a backdrop to the infrastructure framework of the rollover problem within which the occupant and vehicle outcomes were studied. If a NMVCCS-style data collection were to be implemented elsewhere, then complementary manuals produced by federal transportation officials might be consulted producing similar relationships. The current study uses NMVCCS data to describe vehicles travelling through diverse design geometries and the outcome for occupants involved in crashes within that system. Codified and extrapolated data form the basis for assessing NMVCCS and its value to the transportation safety community, as the protocols are applicable universally. The benefit in continuing a NMVCCS-style study is noted, as the interaction of roadway infrastructure and occupant protection agencies might find paths to better work together in solving the complex rollover problem using a common data-driven approach.
The overall purpose of the ASSESS project is to develop a relevant and standardised set of test and assessment methods and associated tools for integrated vehicle safety systems, primarily focussing on currently available pre-crash sensing systems. The first stage of the project was to define casualty relevant accident scenarios so that the test scenarios will be developed based on accident scenarios which currently result in the greatest injury outcome, measured by a combination of casualty severity and casualty frequency. The first analysis stage was completed using data from a range of accident databases, including those which were nationally representative (STATS19, UK and STRADA, SE) and in-depth sources which provided more detailed parameters to characterise the accident scenarios (GIDAS, DE and OTS, UK). A common analysis method was developed in order to compare the data from these different sources, and while the data sets were not completely compatible, the majority of the data was aligned in such a way that allowed a useful comparison to be made. As the ASSESS project focuses on pre-crash sensing systems fitted to passenger cars, the data selected for the analysis was "injury accidents which involved at least one passenger car". The accident data analysis yielded the following ranked list of most relevant accident scenarios: Rank Accident scenario 1 Driving accident - single vehicle loss of control 2 Accidents in longitudinal traffic (same and opposite directions) 3 Accidents with turning vehicle(s) or crossing paths in junctions 4 Accidents involving pedestrians The ranked list highlights the relatively large role played by "accidents in longitudinal traffic", and "accidents with turning vehicle(s) or crossing paths in junctions" (the second and third most prevalent accident scenarios, respectively). The pre-crash systems addressed in ASSESS propose to yield beneficial safety outcomes with specific regard to these accident scenarios. This indicates that the ASSESS project is highly relevant to the current casualty crash problem. In the second stage of the analysis a selection of these accident scenarios were analysed further to define the accident parameters at a more detailed level .This paper describes the analysis approach and results from the first analysis stage.
This work aims at bringing evidence for mass incompatibility in frontal impact for cars built according to the UNECE R94 regulation. French national injury accidents database census for years 2005 to 2008 were used for the analysis. The heterogeneity of frontal self-protection among cars of different masses is investigated, as well as the partner protection parameter offered by these cars. The last part of the analysis deals with the estimation of the benefit, in terms of fatal and severe injuries avoided, if crashworthiness was harmonized for the whole fleet of vehicle. This calculation is done for France and is extended to all Europe.
An analysis of NASS and FARS was conducted to determine crash conditions that involved injuries that are not currently being directly addressed by vehicle safety standards or by consumer information test protocols. Analysis of both field data and US NCAP tests were conducted to determine the relative safety provided by seating position and by vehicle model year. Opportunities for improvements were determined by crash categories with large populations of injuries that were not addressed by safety tests or smaller numbers that were increasing in frequency. Areas of opportunities include improved occupant restrain in rollovers, improved frontal protection for rear seat occupants and improved fire prevention in frontal and rollover crashes.
Since 2005, the motorcycle crash fatalities in the US exceeded 10% of the overall annual traffic fatalities. Consequently, it has become critical to gain in-depth understanding of the factors and characteristics contributing to motorcycle crashes. Unfortunately, there currently exists no database gathering the necessary information for an in-depth analysis of the US motorcycle crashes. So this study utilizes the NASS/CDS database (National Automotive Sampling System, Crashworthiness Data System) in order to gain insights into the patterns and factors leading to a NASS/CDS motorcycle crash, from 1997 to 2007. NASS/CDS samples about 5,000 passenger car tow-away crashes per year. Each case includes photographs and detailed data on crash and pre-crash characteristics, vehicle types, trajectories, types of impact, and other pertinent roadway and crash scene information, allowing an in-depth investigation of the crash mechanisms. However, the NASS/CDS sampling process specifically focuses on passenger car crashes, so the cases extracted only correspond to crashes in which a passenger vehicle was towed, and a motorcycle was somehow involved. Thus, a by-hand in-depth review of about 200 cases allowed retrieving 106 relevant crashes for this study, tending to represent the severe passenger vehicle(s) versus motorcycle(s) crashes on US roads. The findings lead to the conclusion that these crashes mostly result from the low conspicuity of the motorcycle, and from the inability of the car drivers to fully appreciate and anticipate the behavior of a motorcycle. Indeed, it has been shown that, first, the car drivers involved in these cases did not attempt any avoidance maneuver, second, they were largely of ages under 25, and finally, the majority of the crashes were in an intersection scenario. In addition, the two major scenarios unveiled were the car attempting a left turn from the opposite direction and the car attempting a left turn from the right. The paper mentions several solutions to enhance the motorcycle- conspicuity and to allow the car drivers to better anticipate its behavior, which seem to be key factors in the intersection-related crashes (and more generally in the passenger vehicle(s) versus motorcycle(s) crashes).
This study that was funded by the Research Association for Automotive Technology (FAT) develops a method for the evaluation of the placement of tanks or batteries by using the deformation frequencies in real-world accidents. Therefore, the deformations of more than 20.000 passenger cars in the GIDAS database are analysed. For each vehicle a contour of deformation is calculated and the deformed areas of the vehicles are transferred in a rangy matrix of deformation. Thereby, the vehicle is divided into more than 190.000 cells. Afterwards, all single matrices of deformation are summarized for each cell which allows representative analyses of the deformation frequencies of accidents with passenger cars in Germany. On the basis of these deformation frequencies it is possible to determine least deformed areas of all passenger cars. Furthermore, intended placements of tanks or batteries can be estimated in an early stage of development. Therefore, all vehicles with deformations in the intended tank areas can be analysed individually. Considering numerous parameters out of the GIDAS database (e.g. collision speed, kind of accident, overlap, collision partner etc.) the occurring forces can be calculated or the deformation frequency can be estimated. Furthermore, it is possible to consider the influence of primary and secondary safety systems on the deformation behaviour. The analysis of "worst case accident events" is an additional application of the calculated matrix of deformation frequency.
The paper presents a methodology for the benefit estimation of several secondary safety systems for pedestrians, using the exceptional data depth of GIDAS. A total of 667 frontal pedestrian accidents up to 40kph and more than 500 AIS2+ injuries have been considered. In addition to the severity, affected body region, exact impact point on the vehicle, and the causing part of every injury, the related Euro NCAP test zone was determined. One results of the study is a detailed impact distribution for AIS2+ injuries across the vehicle front. It can be stated, how often a test zone or vehicle part is hit by pedestrians in frontal accidents and which role the ground impact plays. Basing on that, different secondary safety measures can be evaluated by an injury shift method concerning their real world effectiveness. As an example, measures concerning the Euro NCAP pedestrian rating tests have been evaluated. It was analysed which Euro NCAP test zones are the most effective ones. In addition, real test results have been evaluated. Using the presented methodology, other secondary safety like the active bonnet (pop-up bonnet) or a pedestrian airbag measures can be evaluated.
Tree impacts are still one of the most important focal points of road deaths in Germany. For the year 2008, the latest figures in the national statistics show a share of 28% of road users killed in crashes with trees alongside a road amongst all crashes on rural roads (except the Autobahn). The official German statistics show the attribute "impact on a tree" since 1995. For this first reported year, the share of road users killed in such crashes was 30%. During the last 14 years, fatal accidents with road users killed on rural roads (except the Autobahn) after impacts on a tree declined by 60% from 1,737 (year 1995) to 696 (year 2008). But this is more or less in line with the general evolution of vehicle and traffic safety in Germany. For Germany as a whole the accident statistics do not show a reduction for "treer crashes" which is clearly more than the average for all accidents. But, as shown with the paper, there are different evolutions in the several German States. In public awareness the topic "tree impacts" is mostly associated with the situation in Germany after the reunification. At that time a lot of road users were killed on the avenues in the so called "new countries". The fact that "tree impacts" are still a big share within the figure of killed road users seems to be little-known. Using updated information coming from the official statistics and in-depth-studies, accident researchers can identify a big potential for further improvements of traffic safety on the associated district roads, state roads and federal highways. There is still a need to analyse more details of the accident occurrence with impacts on trees to generate new and updated findings on the current limits and potentials of measures to improve vehicle and traffic safety. To make further efforts in reducing the figures of victims of "tree impacts" the intensification of well-known conventional solutions " for example implementation of guard rails and reduction of speed - is an option. Measures related to vehicle safety technology especially in the field of primary (active) safety will have additional benefit within the physically imposed limits. With this background it can be seen that the subject "tree impacts" should be analysed with a holistic approach taking into account the entire system of driver, vehicle, road, the environment and a social consensus as well.
Looking at the total of sum of fatal car accidents the number of single-vehicle accidents and particularly run-offroad (ROR) accidents are most frequent. In Austria on the Autobahn ROR accidents amounts to almost 45% of all fatal accidents, i.e. nearly every second fatal accident is caused by ROR accidents and interaction with infrastructure. Approximately 43 people were killed on Autobahns in ROR accidents with passenger cars. One possibility of protection against impacts with infrastructure is the use of guardrails. However, the initial element identified as a turned down terminal could become a dangerous impact object. These turned down terminals may lead a vehicle to roll over or the car "takes-off" when impacting the turned down guardrail. In many cases it is reported that the vehicle is jumping into road side objects such as traffic sign poles or overpasses. On average, nine people are killed in such accidents every year in Austria.
Small overlap frontal crashes are defined by a damage pattern with most of the vehicle deformation concentrated outboard of the main longitudinal structures. These crashes are prominent among frontal crashes resulting in serious and fatal injuries, even among vehicles that perform well in regulatory and consumer information crash tests. One of the critical aspects of understanding these crashes is knowing the crash speeds that cause the types of damage associated with serious injuries. Laboratory crash tests were conducted using 12 vehicles in three small overlap test conditions: pole, vehicle-to-vehicle collinear, and vehicle-to-vehicle oblique (15-degree striking angle). Field reconstruction techniques were used to estimate the delta V for each vehicle, and these results were compared with actual delta V values based on vehicle accelerometer data. Estimated delta Vs were 50% lower than actual values. Velocity change estimates for small overlap frontal crashes in databases such as NASS-CDS significantly underestimate actual values.
Bone fracture patterns could be crucial in reconstructing the nature of loading, especially in the lower limb and upper limb kinematics in vehicle-pedestrian crashes. In addition, use of FE bone models can be a handy tool to predict vehicle impact velocity and the impact direction. The point of fracture initiation in bone loading has been predicted quite accurately earlier. A methodology that predicts bone crack initiation and its propagation pattern for the six known loading directions using a single material and failure model is presented.
Unfortunately, there has been a high number of accident fatalities reported in the Czech Republic in recent years. There are many causes which have led to a growth in the number of road traffic accidents. Since 1990, traffic density has demonstrated an upward moving tendency, daily traffic-jams are on the increase in many cities and traffic capacity on roads and streets is not able to satisfy this increasing density. Moreover, many road users lack experience in terms of driving modern cars. The National Accident Study of the Czech Republic is based on the assumption that the year 2010 is considered as a pilot project with the testing operation of collecting and evaluating data from traffic accidents. From the beginning of 2011, a fully-functional structure of the Traffic Accident Research will be created and solid data generated. Based on this assumption, we hope to begin meaningful cooperation with foreign countries.
Recent findings from real-world accident data have shown that fatality risks for pedestrians are substantially lower than generally reported in the traffic safety literature. One of the keys to this insight has been the large and random sample of car-to-pedestrian crashes available in the German In-Depth Accident Study (GIDAS). Another key factor has been the proper use of weight factors in order to adjust for outcome-based sampling bias in the accident data. However, a third factor, a priori of unknown importance, has not yet been properly analysed. This is the influence of errors in impact speed estimation. In this study, we derived a statistical model of the impact speed errors for pedestrian accidents present in the GIDAS database. The error model was then applied to investigate the effect of the estimation error on the pedestrian fatality risk as a function of car impact speed. To this end, we applied a method known as the SIMulation-EXtrapolation (SIMEX) method. It was found that the risk curve is fairly tolerant to some amount of random measurement error, but that it does become flattened. It is therefore important that the accident investigations and reconstructions are of high quality to assure that systematic errors are minimised and that the random errors are under control.
A national initiative from the vehicle manufacturers, safety system suppliers, the road administration and universities in Sweden took off in 2007. The aim was to develop a national investigation network and a methodology focusing on all phases of a crash (pre-crash, in-crash and post-crash) as well as all parts of the road transport system (road user, vehicle and road environment). The initiative is formally run as a project with the acronym INTACT (Investigation Network and Accident Collection Techniques). It was a three year pilot with the aim to develop methodologies for an extended national crash investigation activity. During the first year the INTACT partners agreed on the aim for the investigation and methods for retrieving the data were developed. During the second and third year the methodology was tested in real-world investigations and further refinement was made. The paper describes the methodology developed to obtain high qualitative in-depth road crash data.
In India, heavy truck crashes on national highways account for a number of fatalities. But due to lack of in-depth crash data, detailed analysis is not possible to determine injury mechanisms, and to identify infrastructure, vehicle and human factors affecting these crashes. Over the past two years, researchers in India have established a crash investigation network, with the co-operation of the police and hospitals, to conduct crash investigations and in-depth crash data collection on national highways in the state of Tamil Nadu. This pioneering effort has resulted in the development of a heavy truck crash investigation methodology, the outcome of which is scientific and reliable crash data that has been able to provide good insight into truck crashes and their causes. This paper explains the need for truck crash investigations, the methodology, conclusions of the data analyzed up to date, and the need to focus on truck driver working conditions.
Providing effective occupant protection in rollover crashes requires supplying the occupant with a restraint system proven effective in the dynamic rollover accident mode. Preventing ejection and providing restraint sufficient to prevent potentially injurious contacts with both interior and exterior vehicle components is paramount for effective rollover occupant protection. Research has shown that the injury potential can be decreased by closely coupling the occupant to the seat. This paper focuses on the effect of restraint system slack and its relationship to occupant excursion and ejection potential during rollover. Various restraint system configurations are evaluated in rollover-type test environments. A review of prior research is presented prior to presenting new quasi-static vehicle inversion studies conducted with live surrogate occupants. Additionally, dynamic rollover testing utilizing anthropometric test devices (ATDs) is presented. The influence of belt looseness and effects of various restraint designs on the belted occupants' injury potential are discussed.
Mechanical properties of tibial bone at compressive strain rates of 50-200 s-1 are obtained through Split Hopkinson pressure bar. Cylindrical specimens of 12-15 mm diameter and 2-5 mm thickness were used. The Young- moduli are calculated from linear portion of stress-strain curves. For both cortical and cancellous part of the bones, the Young- modulus was found to increase with the increasing strain rates. Also for both cancellous and cortical bones the Young- modulus increases consistently with increase in densities.
Among European Countries, Spain first issued a Standard, UNE 135900:2005, further updated in 2008, that deals with homologation and effectiveness evaluation of road restraint systems components designed to reduce harm for bikers impacting on them. An in depth analysis and critical review of this standard is reported in this paper. Beside a close examination of the standard requirements, numerical models of the crash test stated by the standard have been set up and simulated to study the effects of slight speed and approach angle variations on test results, remaining within tolerance gaps allowed by the standard. Model were validated against experimental data. Together with the expected increasing severity of the impact according with speed, a strong influence of approach angle on injury parameters was found. Possible improvements to the norm, in order to make it more robust, are suggested.
The need of passive safety devices, able to reduce the accidents and the severity of injuries suffered by motorcyclist, distinctly arises from data on accident statistics. In this paper, the effectiveness of an airbag device fitted in the biker- garments has been verified through various numerical simulations. Two simple test conditions were defined, in order to investigate the performance of the device both for back and front impacts, and simulated at various impact speeds. With the aim of providing more information about the actual capability of the airbag to reduce the severity of the injuries, one of accident scenario described by ISO 13232:2005 has been also investigated, checking the real effectiveness of the airbag strap-based firing system too. Confrontation of injury indexes resulting from simulation with and without airbag made possible a realistic evaluation of the harm reduction induced by the airbag presence.
Accident data shows that the vast majority of pedestrian accidents involve a passenger car. A refined method for estimating the potential effectiveness of a technology designed to support the car driver in mitigating or avoiding pedestrian accidents is presented. The basis of the benefit prediction method consists of accident scenario information for pedestrian-passenger car accidents from GIDAS, including vehicle and pedestrian velocities. These real world pedestrian accidents were first reconstructed and the system effectiveness was determined by comparing injury outcome with and without the functionality enabled for each accident. The predictions from Volvo Cars" general Benefit Estimation Model are refined by including the actual system algorithm and sensing models for a relevant car in the simulation environment. The feasibility of the method is proven by a case study on a authentic technology; the Auto Brake functionality in Collision Warning with Full Auto Brake and Pedestrian Detection (CWAB-PD). Assuming the system is adopted by all vehicles, the Case Study indicates a 24% reduction in pedestrian fatalities for crashes where the pedestrians were struck by the front of a passenger car.
An eCall device has been mounted on some vehicles in France since 2003. It is an integrated car radio/GSM/GPS system that can be used with a SIM card. When an accident occurs, a call can be sent manually or automatically made to a telephone call centre. Knowing the geographic location, the vehicle identity and the possibility of a direct communication with the people involved enables the nearest emergency services to be called out. In this context, the LAB / CEESAR have set up a study aimed at evaluating the effectiveness of this system. The purpose of this paper is to detail the E-call system evaluation method of effectiveness used and give a global synthesis of the results.
Females sustain Cervical Spine Distortion injury (CSD) more often than males. Most work dealing with the biomechanics background (e.g. injury mechanism/criteria) as well as the application in seat design/testing, focuses on the occupant model of an average male. Therefore the EU-Project ADSEAT (Adaptive Seat to Reduce Neck Injuries for Female and Male Occupants) is aimed at adding a female model for gender balanced research of CSD and improving seat design. An extensive literature review, searching for risk factors and injury criteria for males and females, was accompanied by the evaluation of different databases containing CSD cases. The database evaluations suggests that an anthropometry quite close to the 50%ile female anthropometry as known from crash test dummy design is appropriate. The results presented here form the basis for the future development of a computational female model and the improvement of seat design for better protection of both males and females in the frame of the ADSEAT-Project.
Für den Einsatz im Erdbau des Straßenbaus müssen die eingesetzten Geokunststoffe hohen Qualitätsansprüchen genügen. Das Straßenbauregelwerk ist durch die Veröffentlichung der "Zusätzlichen Technischen Vertragsbedingungen und Richtlinien für Erdarbeiten im Straßenbau" (ZTV E-StB 09) in dieser Hinsicht nun vollständig, so dass eine lückenlose Nachverfolgung der Produkte von der Herstellung über die Lieferung bis zum Einbau möglich ist. Wichtig ist jedoch die Einhaltung der Vorschriften und Anforderungen, angefangen beim Hersteller über den Lieferanten, über den Auftragnehmer bis hin zum Auftraggeber, um einen hohen Qualitätsstandard des Produktes und der fertigen Leistung zu garantieren. Hersteller, deren Produkte einer freiwilligen Überwachung unterliegen, können diese Produkte mit einem Qualitätssiegel kennzeichnen und liefern zusammen mit der CE-Kennzeichnung ein Produktzertifikat. Da in diesem Fall auf die Baustoffeingangsprüfung verzichtet werden kann, reduziert sich der finanzielle und zeitliche Prüfaufwand und es wird ein reibungsloser Bauablauf erzielt.
Die zukünftige Entwicklung der Straßenverkehrssicherheit und damit auch der Fahrzeugsicherheit wird durch gesellschaftliche, wirtschaftliche, klimapolitische und verkehrspolitische Rand- und Rahmenbedingungen und die voranschreitende technische Entwicklung geprägt sein, die auch für den Gesetzgeber eine Herausforderung darstellen. So wird sich auch das Folgeprogramm des Bundesministeriums für Verkehr, Bau und Stadtentwicklung (BMVBS) für das derzeitige aus dem Jahr 2001 stammende "Programm für mehr Sicherheit im Straßenverkehr" an den Schwerpunkten des "4th Road Safety Action Programme" ausrichten, das im Frühjahr 2010 durch die EU-Kommission veröffentlicht werden soll. Im Prozess zu einer weiteren Verbesserung der Straßenverkehrssicherheit werden unter anderem der demografische Wandel in unserer Gesellschaft, die durch eine erforderliche CO2-Reduktion bedingte Einführung alternativer Antriebe (Elektromobilität) verbunden mit Leichtbau sowie die gesetzlichen Rahmenbedingung (Wiener Abkommen) eine bedeutende Rolle spielen. Die Klärung der gesetzlichen Rahmenbedingungen ist unerlässlich, um die Vision vom unfallfreien Fahren Realität werden lassen zu können.